Wagon Progress

Thank you for the pics Robert.
In my trucking days I've been past this place probably 75 times just never took the time to stop.
Always said to myself "I sure would like to wander around in there sometime".
Thanks again, K. Lee
 
Thank you for the pics Robert.
In my trucking days I've been past this place probably 75 times just never took the time to stop.
Always said to myself "I sure would like to wander around in there sometime".
Thanks again, K. Lee
Even more larger trucks in the lot next door, which is owned by his son..
 
Overdue for another update...

We had some dings in the F7 hood to remove that were located in the radius along the sides.. Didn't really have a hammer that fit the exact requirement, so I use a "KIT" that my buddy Will Cronkrite had given me, a piece cut out of a Model A leaf spring.

I had more than one BF603 in stock, and rarely use the pick end, so it became the likely candidate.

IMG_7334.JPG


IMG_7335.JPG


IMG_7336.JPG


TIG welded in place using ER312 rod

IMG_7340.JPG


Some crown added long ways and polished up...

IMG_7345.JPG


IMG_7346.JPG


Both of the Wagon's rear kick panels are now prepped, ready to go..

IMG_7289(1).JPG


IMG_7330.JPG


Vince has the core support and associated parts blocked and ready for some green...

IMG_7378.JPG


IMG_7379.JPG


….and speaking of paint, we got some "new" used light fixtures for the paint booth so we can see a bit better...

IMG_7362.JPG


Old next to new...

IMG_7347.JPG


Now that we can see a bit better, it's clear that the walls need a fresh coat of white...

IMG_7380.JPG


….And some blocking tips on the F7 hood. We have a nice crease on the inside of the hood from front to back. These scratches show that we would be taking material off the adjacent side if no other steps were taken to stop our sanding block at the center of the crease...

IMG_7382.JPG


By adding a strip of tape along the center, it gives us a positive stop for the sanding block..

IMG_7381.JPG


Then switching for the other side....

IMG_7383.JPG


Which leaves us a nice crease in the middle, and panels nice and flat to either side...

IMG_7385.JPG

This is a helpful tip for me seeing as my trunk lid has a center ridge in the middle. Now I know how to keep it there, thank you.
 
This past Saturday I went to the Jalopyrama show, held at the Talbot County Community Center in Easton, MD. I made a stop off at the parking lot of the Double T Diner in Parole, MD first though, had to finalize an online purchase of these two gems...

IMG_9889.JPG



Should be some good overflow storage for the Lennox dies.. Here are some of the pictures from the show.. The Willys Woodie is a one of 6 made.

IMG_9884.JPG


IMG_9883.JPG


IMG_9876.JPG


IMG_9878.JPG


IMG_9858.JPG


IMG_9861.JPG


IMG_9863.JPG


IMG_9864.JPG


IMG_9865.JPG


IMG_9829.JPG


IMG_9830.JPG


IMG_9841.JPG


IMG_9853.JPG


IMG_9855.JPG


IMG_9857.JPG


Cody Walls had two cars there in bare steel, badass to say the least. The Buick has been sectioned and roof pancaked, the 32 is heavily channeled.

IMG_9869.JPG


IMG_9881.JPG


IMG_9886.JPG


IMG_9846.JPG


This show is always a must see, and this year did not disappoint..
 
They may have been wiped down with Gibbs, I think he's used it before. Hard to go to a show like that and not have paw prints all over at the end of the day..
 
  • Like
Reactions: Max
Well after about two months of travel for the day job, hangin TV's....




…..we finally got back to work on the wagon and some long overdue progress. The lift gate has been outfitted with some stainless prop rods...


IMG_9302.JPG



Jared has been working on blocking some of the window garnish moldings, and found some low spots. The long sections on many of these when made at the factory were fabricated in multiple pieces and butt welded together in much the same fashion as band saw blades. The front, exposed side would be sanded smooth and the rear side shows a line of weld slag. (see red outlined circle)


IMG_9305.jpg



So we had a couple that showed low areas, but could not readily metal bump with the slag on the back side.. So another tool was made with a notch to accommodate the weld line....


IMG_9311.JPG



This allowed us to bump up the low areas...


IMG_9307.JPG



….and.....more.....blocking...….


IMG_0197.JPG



IMG_0200.JPG



And we also got started on the fabrication of the fan shroud. Just as with patch panels, you will in most cases find it easier and quicker to make challenging parts in multiple pieces and weld the parts together. Then in other cases you want to try something to see if you can.... I give you one piece fan shroud.


IMG_0161.JPG



IMG_0162.JPG





Getting real close...


IMG_0208.JPG



Needs a bit more work with the linear stretch dies to add some more circumference. Then we will add some bead details and a wired edge for strength. To show how much stretching we've done, the metal has gone from .044 thick to .030 at the flange edge...


IMG_0181.JPG



IMG_0212.JPG



And Mike was busy with buttoning up loose ends that we can do a test fire, hopefully this coming weekend, if we can get a parts delivery before then.


IMG_0198.JPG
 
That looked like a lot of time to get the center bent out and then straightened. And that's having the equipment to do it.
How did you calculate the overall depth of the shroud so that when everything is shaped it will actually fit?
Amazing work, I am always scratching my head wondering how you get it to all work out right. o_O
 
…..How did you calculate the overall depth of the shroud so that when everything is shaped it will actually fit?….
The shroud will mount inside the back flange to the core support. The back edge of the shroud (opening) should roughly sit with about 1/2 of the fan protruding to minimize air turbulence, so the depth was measured from the core support flange to midpoint of the fan blade (front to back). We did leave some extra metal around the outer perimeter to be able to fine tune location, as we still have yet to install hood to verify core support is properly located per hood to fender gaps. We have done cross diagonal measurements, but will install hood for final determination to give us the left to right location of the fan opening.
 
Last edited:
The next couple of posts will seem more of a lessons learned than progress of any sort.. Back in my youth many decades ago I was witness to what occurs when one of your siblings was too big for her britches and back talked my father. A quick back hand and she didn't do that again. From that day on, I have been a firm believer in learning from other's mistakes, so hold on and enjoy the ride. It isn't too painful..


With the fan shroud formed it was time for a bead from the bead roller, and we planned on a wired edge to add strength, concentricity, and improve the looks. From dimensions taken from the rear flange of the core support (our fan shroud mounting location) to the center of the fan worked out to about 1-3/4". So given that height, these are the dimensions we came up with for our beadwork.. Typical wrap for the wire edge is 2.5X the diameter of the wire, so given 3/16 wire our flange for wrapping should be .468 or thereabouts..


IMG_0248.JPG



The bead roller die that matches our wire edge size was not correctly dimensioned to be able to use as a backstop, so some "filler" in the form of rare earth magnets gave us the dimension we were looking for..


IMG_0222.JPG



IMG_0251.JPG



So using the bead roller and the joggle dies from the Biederman hood sides, the bead/wire edge was added to our test sample.


IMG_0253.JPG



IMG_0256.JPG



IMG_0257.JPG



IMG_0263.JPG



That looked about spot on, so the bead roller was used to add the center bead on the fan shroud, and the edge was cut to size and tipped to a 90* angle..


IMG_0269.JPG



IMG_0271.JPG



IMG_0274.JPG



Now to use our joggle dies to add the outer bead detail.... which looks like the shroud mounting flange is in the way.. Did I say one piece fabrication was harder?


IMG_0291.JPG



So a new die is in order, for the bottom we have a sliding lower toolholder so that will accommodate most of the offset there. for the top, we need to stack some dies to get the offset needed.


IMG_0300.JPG



IMG_0303.JPG



The upper die also needed a 45* relief on the bottom for installing the lower die.


IMG_0307.JPG



IMG_0309.JPG



Looks much better...


IMG_0311.JPG



IMG_0316.JPG



Our speed run...




.....and this happens on the last pass..


IMG_0317.JPG
 
So now for some hindsight. When we had done a flat test sample we noticed the edge of the lower die had made a crease (finger point). To alleviate this, I will normally taper the dies so the edges aren't tight together, in hopes of curing exactly that.


IMG_0320.JPG



IMG_0318.JPG



Looking back, this slight defect would have been at the edge of the center bead and likely not noticeable at all. Next, between this taper and the ~1/2" flange not wanting to stretch, the resulting shape matches the bottom die, and pulls the shroud circumference inward.. which was not desired either. So moving forward, rather than a folded flange here we should opt for an offset first for more flexibility in stretching outward for the bead detail, and then fold the flange last.


IMG_0319.JPG



So given our misshapen and slit open fan shroud is no longer viable, what's a person to do? I'm not one to so easily throw in the towel. More accurately, I've been called hard headed. So here we go with the second take of Fan Shroud fabrication. And since we missed this step last time, take a look at this video having just cut out the center hole..




There were absolutely ZERO burrs as can be seen. If your tin snip game is not at this level, please watch this instructional video by my friend and fellow metalshaper Bill Gibson. He will explain exactly what you need to do for the same results...




I had been using tin snips for DECADES and watched this video, quickly learning what I had been doing wrong for so long...


....and then back on the NEW fan shroud, stretch with a blocking hammer on the stump, tip the edge, stretch again, until we are able to get the shroud into the power hammer...


IMG_0343.JPG



IMG_0341.JPG



IMG_0366.JPG



and using the power hammer....






Getting close, we're down to about 10% more to go...


IMG_0388.JPG



In between all that fiasco, Mike was working on getting the car test fired. All the temporary wiring connected, and for some reason we had no fuel pump action. OK, third time we've dropped the tank in a week, and removing the pump we find NO connectivity from the outside ground to the inside ground. WTF?


IMG_0409.JPG



Lo and behold, there is no pass through on the grounds but each (inside and outside) has their own bottom tapped hole. It would appear the tapping occurred PRIOR to the anodize finish, and you know how well that conducts.. The burnishing brushes wouldn't touch the stuff, so we used some sharp implements of destruction to allow a ground path...


IMG_0410.JPG



IMG_0412.JPG



That fixed the issue, one that should not have been there from the start. Next, in the interest of safety, lets move the rear "lift kit" from the tires to just inboard using jack stands..


IMG_0413.JPG



IMG_0414.JPG



So now with a bit of fuel pressure to work with, we give you a rumble... We still need to adjust the air/fuel ratio but it was good to hear this after everything else the past couple weeks..


 
More progress on the (second) fan shroud, but I had a request to show the process in greater detail.. So we'll start with the beginning.

First was the layout of the bend line, and then the cut line was located about 3" inside of that. (I'm using some of the pictures from our first attempt as our shop photographer missed some the second time around)


IMG_0162.JPG



The initial stretch was done using a blocking hammer on the top (flat area) of the stump, primarily at the inside edge as that needed the most stretch.


IMG_0441.JPG



On our first attempt we had a hammer form that was used to "set" the bend line with a crowned body hammer as we added the first bit of stretch.


IMG_0451.JPG



This seemed a bit cumbersome, and the second version I used a bent portion of round stock that was in the scrap pile, added a piece of pipe for a handle, and the band saw added a slice for a new tipping tool. The bend in the tipping tool gave it a built in fulcrum. Normally a tipping operation tries to pull the adjacent material along as the bend forms. In this case we set the panel on a table and used the bend (fulcrum) of the tipping tool against the table to pull the stretched area downward. This allows us to push down on the handle to elevate the panel off the table, and to push downward on the flat panel outside the bend line with the palm of your hand. This does a good job of placing the bend where needed without pulling adjacent metal along for the ride. Even though the pictures show the stretched area upward, the panel was placed with this area downward when using the tipping tool..


IMG_0341.JPG



IMG_0342.JPG



IMG_0343.JPG



This worked much better at setting the bend line than the hammer form, and it was surprisingly accurate.


Much of the stretch was done using linear stretch dies on the power hammer, but we also reverted back to the blocking hammer and stump to better focus the stretch locations.






IMG_0442.JPG



The other issue to overcome with both hammer operations was that they didn't play nice with keeping the shroud in a flat vertical. So the next tool used was a 90 durometer pad of polyurethane and the Model A leaf spring hammer. The hammer face was too short to match the shroud height (approx 3") so three passes were done to cover the entire height and with each pass the hammer hits were about 1/8" or so apart.


IMG_0443.JPG



IMG_0444.JPG



IMG_0445.JPG



IMG_0446.JPG



The bulk of the stretch was done on the power hammer, and the front of the lower die holder is missing quite a bit of paint from this job...


IMG_0447.JPG



The completed bend, we started with .044 thickness (18 gauge) and it was thinned to .029 thick, or lost about 1/3 thickness to turn the 90...


IMG_0437.JPG



IMG_0438.JPG



IMG_0439.JPG



IMG_0440.JPG



 
More progress... using our rare earth magnets on the end of the bead roller die to correct the "back spacing", the fan shroud has the center bead added...


IMG_0250.JPG





Next, adding the outer joggle for the wire. Our last mis-step at this stage was expecting a folded flange to perform as it did on a flat piece of metal.. But as a full circle with 1/2" of flange, it tends to resist any change in diameter, so our efforts to add the joggle (stretch outward) were met with catastrophic failure in the way of a split. This next attempt will leave that edge straight out instead of flanged, such that it will be more apt to move/stretch as we need it to.. Additionally, our dies will have a backstop built in and include two bead forming details. One will follow the center bead already installed, and with the back stop as part of the die, should correct any wiggle our bead roller may have added. Having both bead details added to the dies will also help to maintain correct spacing throughout. As these beading dies tend to pull material from either side, having multiple beads makes it more of a challenge to pull sufficient material for both and have enough for the bead height.. Adding one prior using the bead roller means we will only be "pulling" material for the one, for better results.


IMG_0497.JPG



Our test sample shows the wrap for the wire straighter to the side, for less resistance to adding the offset.


IMG_0496a.jpg



Shroud is then trimmed to size and run through the dies on the Lennox..


IMG_0510.JPG



IMG_0513.JPG



IMG_0514.JPG



IMG_0515.JPG



This did give us a slight potato chip shape of the panel, so the offset was stretched in the Erco..


IMG_0517.JPG



IMG_0518.JPG



Our tubing straightener is used to make our 3/16 wire more concentric for an easier install..


IMG_0509.JPG



Then the wire was test fit...


IMG_0519.JPG



IMG_0520.JPG



Mike got our interior assembly and wiring started, the rear tail light / fuel door actuator was installed, the sub box and amp installed, and our relays for the fuel door mounted adjacent to the amp, all tucked away behind the rear seat.


IMG_0492.JPG



IMG_0494.JPG



IMG_0523.JPG



IMG_0525.JPG
 
Back
Top