First time spraying spi epoxy

If somebody struggles with the usability of this epoxy they probably struggle with pouring a bowl of cereal as well.
Thanks for your support. Trust me I’ll figure it out without without your help. I’ve been out of the game for 30 years so new to all this hvlp stuff. I could lay imron like glass with my siphon feed binks stuff back in the day and a few cars won awards for paint at the local shows but I’m starting at a disadvantage with the new stuff. I’m in the middle of restoring a 70 z28 right now so I’m now down to the body and paint.
 
Hey that's a nice clean shop too!
.
.
.
Yeah tight space with 2 car garage. Also car body is on the rotisserie which crowds things even more (too steep of driveway to roll it out, . Since I just have an exhaust fan set up and no inlet filter so cleaning the shop to paint epoxy primer seemed a waste. It actually stayed pretty dust free.

I’ll be doing any finish work in a spray booth I have access to but it’s a fair distance to drive. unfortunately I can’t even rent shop space around here (norrthern calif) as there’s nothing available and if it was it would be an easy $3k a month. This state sucks!
 
For epoxy I’m using a cheap throwaway tcp with 1.4, 26psi airpressure, full open fluid a d 1/2 turn in on the fan. I know this is a cheap gun so maybe asking too much. My base/clear gun os an awata w400.
The recommendation for most guns is 3 turns out on fluid for a starting point.
If you have the nice Iwata, why not use it for the epoxy? Epoxy sprays great with a base gun. Not like it is going to hurt the gun.
 
For epoxy I’m using a cheap throwaway tcp with 1.4, 26psi airpressure, full open fluid a d 1/2 turn in on the fan. I know this is a cheap gun so maybe asking too much. My base/clear gun os an awata w400.
The fan and air are ok, but full fluid??
Turn in until it stops, then turn out three exact full turns

Make sure no internal strainers in the gun.
Hold the gun 5 to 6 inches away from the panel!!!!!
 
If you are referring to me that’s floor film from a previous build. I pull it up and replace just before final paint for each build. But ya, looks bad at this stage of a build… :). At that point it has survived many coats of primer and even bedliner.
Don,
What brand of floor film do you use and how does it hold up? Is it easy to remove?
Anyone else use floor film?
 
Wow, 70 z28, that would be a nice build. Keep us updated on progress. Those are the era of Camaros I grew up with.
 
Thanks for your support. Trust me I’ll figure it out without without your help. I’ve been out of the game for 30 years so new to all this hvlp stuff. I could lay imron like glass with my siphon feed binks stuff back in the day and a few cars won awards for paint at the local shows but I’m starting at a disadvantage with the new stuff. I’m in the middle of restoring a 70 z28 right now so I’m now down to the body and paint.
The comment wasn't directed at you, but somebody who is too put out because they have to wait 30 minutes to induce and 30 minutes between coats.
 
The comment wasn't directed at you, but somebody who is too put out because they have to wait 30 minutes to induce and 30 minutes between coats.
Sorry I took it wrong. Tbh the induction and respray time is kinda nice. Shooting lacquer back in the day it was laying on one coat of paint followed asap with the next.
 
Wow, 70 z28, that would be a nice build. Keep us updated on progress. Those are the era of Camaros I grew up with.
I actually have a whole thread with pics from start to the current point. It’s an all original citrus green m21 4 speed car with factory 4.10s. If you are interested in checking it out the links below. I’m a better mechanic than painter as you’ll find out reading it

 
Don,
What brand of floor film do you use and how does it hold up? Is it easy to remove?
Anyone else use floor film?
I used to use this RBL film. It can be a bear to remove. Stands up well.

I got cheap and I’m currently working through a roll of Binks booth paper. Not as rugged.

Don
 
I used to use this RBL film. It can be a bear to remove. Stands up well.

I got cheap and I’m currently working through a roll of Binks booth paper. Not as rugged.

Don
At my old job we used binks spray envelope on wet booths, mainly on the walls. Cleaned and resprayed those every week. The floors were sprayed but they chiseled them every 3 months. What a mess... They didn't want to spend the time cleaning the floors more often.
Don't know how well it would hold up to traffic on a floor or how often you'd have to strip it to keep it nice.

John
 
Unreduced white epoxy on the door. DV1 1.4 22 psi on top digital gauge.
trailer door epoxy.jpg
 
Back
Top